Tag - Lt

CCNA Switching Question
Short Question CCNA part 8

CCNA Switching Question

Question 1

Which of the following are true regarding bridges and switches? (Choose two)

A. Bridges are faster than switches because they have fewer ports.
B. A switch is a multiport bridge.
C. Bridges and switches learn MAC addresses by examining the source MAC address of each frame received.
D. A bridge will forward a broadcast but a switch will not.
E. Bridges and switches increase the size of a collision domain.


Answer: B C

Question 2

Which two commands correctly verily whether port security has been configured on port FastEthernet 0/12 on a switch? (Choose two)

A. SW1# show switchport port-security interface FastEthernet 0/12
B. SW1# show switchport port-secure interface FastEthernet 0/12
C. SW1# show port-security interface FastEthernet 0/12
D. SW1# show running-config


Answer: C D

Question 3

Assuming the default switch configuration which vlan range can be added modified and removed on a Cisco switch?

A. 2 through 1001
B. 1 through 1001
C. 1 through 1002
D. 2 through 1005


Answer: A

Question 4

Which set of commands is recommended to prevent the use of a hub in the access layer?

switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security maximum 1

switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security mac-address 1

switch(config-if)#switchport mode access
switch(config-if)#switchport port-security maximum 1

switch(config-if)#switchport mode access
switch(config-if)#switchport port-security mac-address 1


Answer: C


Port security is only used on access port (which connects to hosts) so we need to set that port to “access” mode, then we need to specify the maximum number of hosts which are allowed to connect to this port -> C is correct.

Note: If we want to allow a fixed MAC address to connect, use the “switchport port-security mac-address <MAC address>” command.

Question 5

A Catalyst 2950 needs to be reconfigured. What steps will ensure that the old configuration is erased? (Choose three)

A. Erase flash.
B. Restart the switch.
C. Delete the VLAN database.
D. Erase the running configuration.
E. Erase the startup configuration.
F. Modify the configuration register.


Answer: B C E

Question 6

The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?

A. Lower the bridge priority number.
B. Change the MAC address of the switch.
C. Increase the VTP revision number for the domain.
D. Lower the root path cost on the switch ports.
E. Assign the switch an IP address with the lowest value.


Answer: A

Question 7

Which two of these are characteristics of the 802.1Q protocol? (Choose two)

A. It is a layer 2 messaging protocol which maintains vlan configurations across network.
B. It includes an 8-bit field which specifies the priority of a frame.
C. It is used exclusively for tagging vlan frames and dose not address network reconvergence following switched network topology changes.
D. It modifies the 802.3 frame header and thus requires that the FCS be recomputed.
E. It is a trunking protocol capable of earring untagged frames.


Answer: D E


IEEE 802.1Q is the networking standard that supports Virtual LANs (VLANs) on an Ethernet network. It is a protocol that allows VLANs to communicate with one another using a router. 802.1Q trunks support tagged and untagged frames.

If a switch receives untagged frames on a trunk port, it believes that frame is a part of the native VLAN. Also, frames from a native VLAN are not tagged when exiting the switch via a trunk port.

The 802.1q frame format is same as 802.3. The only change is the addition of 4 bytes fields. That additional header includes a field with which to identify the VLAN number. Because inserting this header changes the frame, 802.1Q encapsulation forces a recalculation of the original FCS field in the Ethernet trailer.

Note: Frame Check Sequence (FCS) is a four-octet field used to verify that the frame was received without loss or error. FCS is based on the contents of the entire frame.

Question 8

What are two advantages of Layer 2 Ethernet switches over hubs? (Choose two)

A. decreasing the number of collision domains
B. filtering frames based on MAC addresses
C. allowing simultaneous frame transmissions
D. increasing the size of broadcast domains
E. increasing the maximum length of UTP cabling between devices


Answer: B C


Hub is considered a layer 1 device. When a packet arrives at one port, it is copied to the other ports without checking the content of that packet.

Switch operates at layer 2. When a packet arrives at one port, it checks in its database (based on MAC address) to see which port it should forward that packet out -> B is correct.

Remember that hubs can only communicate in half duplex mode, which means that a computer can only send data when it is not receiving. Switches can run in full duplex mode, which allows data to be sent and received at the same time. Switches effectively double the speed of the network when compared to hubs -> C is correct.

Switch increases the number of collision domains (which is better) -> A is not correct.

Switch does not have any effect on the size of broadcast domains. When using switch, the size of broadcast domains remain the same -> D is not correct.

Both hub and switch increase the maximum length of UTP cabling between devices so it is not an advantage of switch over hub -> E is not correct.

Question 9

Which command will show the MAC addresses of stations connected to switch ports?

A. show mac-address
B. show arp
C. show table
D. show switchport


Answer: B


There is no “show mac-address” command. But notice the “show mac-address-table” and “show mac address-table” do exist.

If option A is “show mac-address-table” then both A & B are correct!

Short Question CCNA part 8

81 – Interface 0/0 what does it mean?

Card number / card interface number

82- When written <CR > what does it mean?

Command complete

83- Which command we give if router IOS stucked?

Crl +Shift+F6 and X

84- Which command we give for see routing table?

Show ip route

85 – What does synchronization mean ?

Routers are ready to communication with each other

86- What does routing mean ?

For best path selection

87- What is difference between static and dynamic routing?

In Static route we add others connected network and in dynamic, we advertise our network

88- Which type of routing you did in CCNA?

Traditional Routing

89 – How many parts of Ping?

Tow parts – eco and eco reply

90- When we do default route?

When there is multiple destination and single gateway.

91 – What is difference between routing and routed protocols?

i) Routing use for best path selection

ii) Routed protocol keeps source and destination information.

92- What is difference between IGP and EIGRP?

IGP = use in Autonomous and EIGP = use with multiple autonomous

IGP= Interior gateway routing protocol.

EIGRP= Enhanced Interior Gateway routing protocol

93 – Why we use debug command?

For live view

94 Which command we give for live view of remote site routers ?

Terminal monitor

95- Which protocol used before part of CCNA?


CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Copyright © 2024. Created by IT Learning. Powered by DumpsForAll | Terms of Use | Privacy Policy