Tag - switch

1
CCNA Interview Questions
2
Interview Question of CCNA Part 6
3
Interview Question of CCNA Part 2

CCNA Interview Questions

After Review CCNA course we Conclude some short Questions with Answers

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Interview Question of CCNA Part 6

51- What is the subnetmask of / 27 in network based and host based ?

In network based 224 { 128+64+32}and in host based 248 (128+64+64+16+8)

52- What will be the prefix length of 224 in VLSM ?
27 (carry 3 bits from host (128+64+16=224) and add in network ports (24+3=27) )

53-How many valid IP will b in /21 in route Summarization?

1044

54- In which protocol you manually enable route summarization ?
OSPF

55 – In which protocol supenetting is enable by default?

RIPv2 and EIGRP

56- What is MAC address size of IPv6?

64 bits

57 – Default Packet Size of IPv6?
8 Bytes = 16*8 =128 bit

58- How many fillers we can put in one IP of IPv6?
ONE (:: called filler)

59- Which mathematically form used inIPv6?
Hexadecimal

60- What is quality of IPv6?

a)    Router processing will rapid because field size wills 8 bytes (but in IPv4 it was 12 byres)

b) No Fragmentation

c) No Checksum

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Interview Question of CCNA Part 2

11- What is the difference between bus topology and HUB?

Hub is Centralized device ( series ) .Bus topology is Decentralized device (in parallel)

12- Is hub intelligent device?
No; because it not use header

12- Which protocol switch use for filling its MAC-Table ?
ARP – Address Resolution Protocol

13- What is CAM ?
Content Address Memory. its another name of MAC address table.

14- Which type for communication switch do?
In case of any new event switch do broadcast, after that always do Unicast.

15- If line down and protocol also down; in this case which layer move problem?
Physical Layer – Layer 1

16 – If line up, but protocol down which layer should be troubleshot?
Data link problem – Layer 2

17-On which base switches take decisions?
Mac Address

18- How ARP brings MAC address for switch?
Through Broadcast

19- How many collision domains are in switch?
Equal number of ports

20- How many broadcast domains are in Switch ?
One

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Copyright © 2024. Created by IT Learning. Powered by DumpsForAll | Terms of Use | Privacy Policy