Dumps For All – Page 9 – Online IT Study Material

Short Question CCNA EIGRP

146- After how long keep alive messages exchange in EIGRP?

5 SECONDS

147- Which type of updates EIGRP protocol do?

INCREMENTAL UPDATES (CHANGE BASE)

148- What is the draw back of EIGRP protocol?

CONFIGURE ONLY ON CISCO ROUTERS

149- What is the matric of EIGRP protocol?

i) Bandwidth

ii) Load

iii) Delay

iv) Reliability

v) MTU

vi) Maximum Transmission Unit

150- In EIGRP metric parameters which 2 Options are enable by default?

i) Bandwidth

ii) Delay

151- Which protocol can do load balancing on unequal cost also?

EIGRP

152- 1350 value in which type of Access-list?

STANDARD ACCESS-LIST

153- 1900 value in which type of Access list?

STANDARD ACCESS-LIST

154- 2500 value in which type of Access list?

EXTENDED ACCESS-LIST

155- What is the difference between named and Extended ACL?

In named Access-list we can edit and also give name

156- When we use standard Access-List?

When there is no Destination

157- When we use extended Access-List?

When there is source and Destination

158- What is the default behavior of Access-List?

Deny

159- On which interface we always Apply Access-List?

Fast Ethernet

160- Wild card mask always in odd value or even

ODD

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Short Question of CCNA OSPF

123- On which bas OSPF take decision?

LINK COST

124- What is default cost of serial interface in OSPF?

64

126- How many types of OSPF Configuration?

There are Two Types

A ) SINGLE AREA

b) MULTI AREA

127- What is hold down time formula of OSPF?

HELLO PACKETS*4=40SECONDS

128 – What is the default bandwidth size of T1 Routers?

1544BYTES

129- If bandwidth will increase what will happen?

SERIAL COST WILL DECREASE

130- What is the command for change serial cost?

IP OSPF COST (which want to set)

131- When DR communicate with BDR which multicast ip it use ?

224.0.0.6

132- What is the draw back of OSPF protocol?

i) Single Area

ii) High Hardware Requirements

iii) Troubleshooting

133- Which protocol comes under Hybrid dynamic type?

EIGRP (ENHANCED INTERIOR GATEWAY ROUTING PROTOCOL)

134- Which protocol works only on Cisco routers?

EIGRP (ENHANCED INTERIOR GATEWAY ROUTING PROTOCOL)

135- What is the size of Hello Packets in EIGREP protocol?

50 BYTES

136- How much hold down time of EIGREP protocol?

15 SECONDS

137- Formula of Hold down time of EIGRP protocol?

HELLO PACKETS*5=15SECONDS

138- After how long EIGRP protocol Advertise its routing table?

5SECONDS

139- Which multicast IP EIGRP protocol use?

224.0.0.10

140- Which protocol called Rapid protocol?

EIGRP

141-What is the name of Algorithm of EIGRP protocol?

DUAL(DIFFUSING UPDATES ALGORITHM)

142- How many hop counts are by default and how much you can increase in EIGRP protocol?

By default 100 counts, and maximum 25

143- How much internal and External AD of EIGRP protocol?

Internal =90 and Externa =170

144- What is the name of best path in EIGRP protocol?

SUCCESSOR

145- What is the second best path name of EIGRP?

FEASIBLE SUCCESSOR

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

CCNA Interview Questions

After Review CCNA course we Conclude some short Questions with Answers

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Interview Question of CCNA Part 6

51- What is the subnetmask of / 27 in network based and host based ?

In network based 224 { 128+64+32}and in host based 248 (128+64+64+16+8)

52- What will be the prefix length of 224 in VLSM ?
27 (carry 3 bits from host (128+64+16=224) and add in network ports (24+3=27) )

53-How many valid IP will b in /21 in route Summarization?

1044

54- In which protocol you manually enable route summarization ?
OSPF

55 – In which protocol supenetting is enable by default?

RIPv2 and EIGRP

56- What is MAC address size of IPv6?

64 bits

57 – Default Packet Size of IPv6?
8 Bytes = 16*8 =128 bit

58- How many fillers we can put in one IP of IPv6?
ONE (:: called filler)

59- Which mathematically form used inIPv6?
Hexadecimal

60- What is quality of IPv6?

a) Router processing will rapid because field size wills 8 bytes (but in IPv4 it was 12 byres)

b) No Fragmentation

c) No Checksum

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Interview Question of CCNA Part 5

1

41- When we use loop back IP?

For Self hardware test

42- When IP confliction accord in subnet which IP assigned automatically and what it called?
169.254.x.x APIPA (Automatic Private Internet Protocol address)

43- What is the minimum and maximum request timer?

Minimum = 180 sec
Maximum = 300 Sec

44- Which company mange IP’s?
IANA (Internet Assigned Number of Authority)

45- Which classes are assignable?
A, B and C

46- How many potions of IP?
Two portions of IP. Network and host

47-Do we subletting of IP?
NO, we do subletting of NID

48- What is subnetting ?
Subnetting is tool reduce the wastage of IP

49- What is CIDR ?
Class Less Inter domain Routing Protocol – another name of Supernetting.

50- What is difference between FLSM and VLSM?
In FLSM subnet mask of all subnets will b same. But in
FLSM it varies.

CCNA Interview Question Part 1

CCNA Interview Question Part 2

CCNA Interview Question Part 3

CCNA Interview Question Part 4

CCNA Interview Question Part 5

CCNA Interview Question Part 6

CCNA Interview Question Part 7

CCNA Interview Question Part 8

CCNA Interview Question Part 9

CCNA Interview Question Part 10

CCNA Interview Question Part 11

CCNA Interview Question Part 12

CCNA Interview Question Part 13

CCNA Interview Question Part 14

Copyright © 2024. Created by IT Learning. Powered by DumpsForAll | Terms of Use | Privacy Policy